Nissan Micra K12 Extended Wheel Stud Set - M12 x 1.25

Upgrade the wheel mounting hardware on your Nissan Micra K12 with this complete set of extended wheel studs.

Supplied as a 20-piece set with an M12 x 1.25 thread, these extended studs are ideal for modified K12s where additional stud length is required, particularly when fitting wheel spacers or certain aftermarket wheel configurations.

Key Features

• Designed for the Nissan Micra K12
• 20-Piece Complete Set
• Extended Wheel Stud Design
• M12 x 1.25 Thread
• Suitable for Modified Wheel Setups
• Ideal for Use Where Additional Thread Engagement is Required
• Useful with Compatible Wheel Spacers
• Suitable for Road, Fast-Road & Motorsport Builds
• Reference: 7618

Specification

Quantity: 20 Studs
Thread: M12 x 1.25
Type: Extended Wheel Stud
Reference: 7618
Application: Nissan Micra K12

Why Fit Extended Wheel Studs?

The factory wheel studs are designed around the original Nissan wheel and hub arrangement.

When fitting certain aftermarket wheels or wheel spacers, the effective amount of stud available for the wheel nut can be reduced.

Extended wheel studs provide additional stud length, allowing a suitable amount of thread engagement to be maintained where the modified wheel arrangement requires it.

They are particularly useful for:

• Wheel Spacer Installations
• Aftermarket Wheels
• Track Wheel Setups
• Motorsport Builds
• Modified K12s
• Replacement of Existing Extended Studs

⚠️ Correct Thread Engagement Is Essential

Extended studs should not be used simply because a vehicle is modified.

The wheel nut must have suitable thread engagement for the particular wheel, spacer and stud combination being used.

Insufficient engagement can result in wheel mounting failure.

The installer is responsible for confirming that the complete wheel mounting arrangement is suitable for the vehicle and intended use.

M12 x 1.25 Thread

These studs use an:

M12 x 1.25 Thread

Wheel nuts must have the correct M12 x 1.25 thread.

The wheel nut seating profile must also match the wheel being fitted.

Depending on the wheel, this may include different seating arrangements such as tapered, radius or flat-seat designs.

⚠️ Wheel Nuts Are Not Included

Unless specifically stated otherwise, this listing is for the extended wheel studs only.

Existing wheel nuts should only be reused if their thread, seating profile, condition and dimensions are suitable for the new installation.

Ideal for Wheel Spacer Installations

One of the most common reasons for installing extended studs is the use of slip-on wheel spacers.

A spacer moves the wheel further away from the hub and therefore reduces the amount of original stud protruding through the wheel.

Extended studs can compensate for this by providing additional usable stud length.

However, the suitability of any spacer installation depends on more than stud length alone.

The installer should also consider:

• Spacer Thickness
• Hub Location
• Wheel Centre Bore
• Wheel Offset
• Tyre Clearance
• Suspension Clearance
• Arch Clearance
• Wheel Nut Engagement
• Wheel Nut Seating
• Stud & Hub Compatibility

⚠️ Stud Length

These are supplied as extended wheel studs, but a specific overall length or amount of additional length has not been stated in the product specification.

If your installation requires a particular minimum stud length, this should be confirmed before ordering.

Do not select wheel studs based solely on the M12 x 1.25 thread size.

Professional Installation Recommended

Wheel studs are safety-critical components.

Professional installation is strongly recommended.

The original studs must be removed and the replacements correctly installed into the hub without damaging the hub or stud splines.

During installation, check:

• Hub Condition
• Stud Seating
• Stud Spline / Knurl Compatibility
• Brake Component Clearance
• Wheel Clearance
• Spacer Fitment where applicable
• Wheel Nut Thread
• Wheel Nut Seating Profile
• Available Thread Engagement

The studs must seat fully and squarely against the hub.

Do Not Pull Studs into Place Incorrectly

Using excessive force or unsuitable methods to pull a wheel stud into the hub can damage the stud, hub, threads or wheel mounting components.

Appropriate installation equipment and procedures should be used.

Wheel Nut Torque

Wheel nuts must be tightened to the correct specification using a calibrated torque wrench.

The wheel mounting hardware should be rechecked following the appropriate initial bedding period after installation.

Never use damaged, cross-threaded or incorrectly seated wheel nuts.

What's Included?

• 20x Extended Wheel Studs
• M12 x 1.25 Thread

Enough studs are supplied for a complete vehicle set where five studs are used per wheel.

Wheel nuts, wheel spacers and other wheel mounting components are not included unless specifically stated.

Compatibility

Designed for applicable:

Nissan Micra K12

Reference: 7618 Extended Wheel Studs

⚠️ Important Compatibility Check

Thread size alone does not determine whether a press-in wheel stud is compatible with a hub.

The stud's spline / knurl diameter, seating design and overall dimensions must also be suitable for the hub.

Compatibility should therefore be confirmed before installation, particularly on vehicles fitted with non-standard hubs or brake conversions.

Manufacturer Warranty

This product is supplied subject to the applicable manufacturer's warranty terms and conditions.

Wheel studs are safety-critical service components. Warranty does not normally cover damaged threads, incorrect installation, damaged hub splines, cross-threading, over-torquing, impact damage, unsuitable wheel/spacer combinations or use with incompatible wheel nuts.

GizFab Motorsport Developments is an independent aftermarket retailer and is not affiliated with, sponsored by, approved by or endorsed by Nissan Motor Co., Ltd. Nissan and Micra names are used solely for vehicle identification and compatibility purposes.