Nissan Micra K12 Front Lower Arm Inner Uprated Rubber Bush Set

Refresh the front suspension of your Nissan Micra K12 with this uprated rubber front lower arm inner bush set.

Supplied as a 2-piece set, these bushes replace the original inner lower control arm / wishbone bushes, helping restore more positive suspension location and reduce unwanted movement from ageing factory rubber components.

An ideal replacement for worn original bushes and a useful upgrade for standard, lowered and fast-road K12s.

Key Features

• Designed for the Nissan Micra K12
• Front Lower Arm Inner Bushes
• 2-Piece Set
• Uprated Rubber Construction
• Replaces Ageing OEM Rubber Bushes
• Improved Lower Arm Location
• Helps Reduce Unwanted Suspension Movement
• More Positive Steering & Suspension Response
• Road-Friendly Alternative to Solid / Spherical Mounting
• Suitable for Standard & Modified Vehicles
• Reference: Q0951

⚠️ Inner Bushes Only

This listing is specifically for the inner bushes of the front lower control arms.

It is not the complete 4-piece front lower control arm bush set.

What's Included?

• 2x Front Lower Arm Inner Uprated Rubber Bushes

One bush is supplied for each side of the vehicle.

Other lower control arm bushes, ball joints, control arms and mounting hardware are not included unless specifically stated.

Why Replace the Original Bushes?

The lower control arm bushes locate the front suspension while allowing the controlled movement required as the suspension operates.

Over time, the original rubber can deteriorate through age, mileage and exposure to the elements.

Worn bushes may become:

• Cracked
• Perished
• Torn
• Excessively Soft
• Separated from their Sleeves
• Excessively Compliant

This can allow the lower control arm to move more than intended during braking, acceleration and cornering.

Depending on the condition of the existing bushes, replacing worn components can help restore more consistent steering and suspension behaviour.

Uprated Rubber Construction

These replacement bushes use an uprated rubber construction, providing firmer suspension location while retaining the compliance associated with a rubber-bushed suspension system.

This provides a useful middle ground between soft ageing factory bushes and more aggressive solid or spherical-bearing suspension components.

They're particularly suitable for:

• Daily Drivers
• Fast-Road K12s
• Lowered Vehicles
• Performance Builds
• Suspension Restorations
• Occasional Track Use

Some increase in suspension feedback may be noticeable compared with heavily worn or softer original bushes.

Ideal for Lowered & Modified K12s

Lowering the vehicle, fitting performance tyres or increasing cornering loads can place additional demands on suspension bushes.

Reducing unwanted movement at the lower arm mounting points can help maintain more consistent suspension geometry under load.

For best results, the condition of the complete front suspension should be considered rather than replacing individual components in isolation.

Installation

Lower control arm bushes are safety-critical suspension components and professional installation is recommended.

Removal of the original bushes and installation of the replacements may require suitable pressing or specialist bush installation equipment.

During installation, inspect:

• Front Lower Control Arms
• Remaining Lower Arm Bushes
• Ball Joints
• Mounting Bolts
• Chassis / Subframe Mounting Points
• Bush Housings
• Anti-Roll Bar Components
• Surrounding Suspension Components

Any damaged, cracked or heavily corroded components should be repaired or replaced before the vehicle is returned to use.

Correct Bush Orientation

The replacement bushes must be installed in the correct orientation where applicable.

Where the bush design requires final tightening at normal operating ride height, the appropriate installation procedure should be followed to avoid unnecessarily preloading the rubber.

Wheel Alignment Recommended

Following lower control arm bush replacement, we recommend carrying out a professional wheel alignment.

Replacing worn bushes can alter the resting position of the suspension compared with the previous deteriorated components, so alignment should be checked before returning the vehicle to normal use.

Compatibility

Designed for applicable:

Nissan Micra K12 - Front Lower Arm Inner Bushes

Reference: Q0951 Lower Arm Bushing

Please confirm the suspension arrangement on imported, converted or unusually specified vehicles before ordering.

Manufacturer Warranty

This product is supplied subject to the applicable manufacturer's warranty terms and conditions.

Suspension bushes are service components and warranty does not normally cover normal wear, incorrect installation, contamination, accident damage, damaged control arms or mounting points, or use outside the intended application.

GizFab Motorsport Developments is an independent aftermarket retailer and is not affiliated with, sponsored by, approved by or endorsed by Nissan Motor Co., Ltd. Nissan and Micra names are used solely for vehicle identification and compatibility purposes.